ASA Settings for Snapmaker J1
Recommended slicer settings for printing ASA on the Snapmaker J1 (300 x 200 x 200 mm build volume, 350 mm/s max speed, direct drive extruder).
Slicer Configuration
Copy these values into your slicer (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| Setting | Value | Range |
|---|---|---|
| Nozzle Temperature | 250°C | 240-260°C |
| Bed Temperature | 100°C | 90-110°C |
| First Layer Nozzle | 255°C | +5°C above normal |
| First Layer Bed | 100°C | At printer max |
| Print Speed | 100 mm/s | 50-150 mm/s |
| First Layer Speed | 25 mm/s | 25-50% of normal |
| Wall Speed | 75 mm/s | 70-80% of normal |
| Travel Speed | 225 mm/s | 120-150% of print speed |
| Layer Height | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| Wall Count | 2-3 | Perimeters/shells |
| Top/Bottom Layers | 3-4 | Solid layers |
| Cooling Fan | 0-10% | From layer 2+ |
| Retraction Distance | 0.8-1.2 mm | Direct drive |
| Retraction Speed | 40 mm/s | Direct drive |
Before You Print
Print Quality Profiles
Three presets for common use cases with ASA on the Snapmaker J1.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 150 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 100 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 50 mm/s | 20-30% | Miniatures, display pieces, fine detail |
Bed Adhesion
ASA uses the same bed adhesion methods as ABS: PEI sheet at high temperature, glue stick, or ASA/ABS slurry. A brim is recommended for larger parts to prevent warping.
Temperature Tuning Guide
Nozzle: 250°C
Range: 240-260°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 100°C
Range: 90-110°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
Troubleshooting ASA on Snapmaker J1
Pro Tips for ASA
ASA is essentially outdoor-grade ABS -- the go-to for any part exposed to sunlight
While more forgiving than ABS, an enclosure still dramatically improves print quality
Use the same post-processing techniques as ABS; ASA can be acetone-smoothed
For best UV performance, choose lighter colors which resist fading better
Store in a dry box and dry before use if the spool has been open for more than a few days
Support Settings
For prints requiring supports with ASA, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Snapmaker J1 Specs
| Build Volume | 300 x 200 x 200 mm |
| Max Speed | 350 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 100°C |
| Extruder | Direct Drive |
ASA Properties
| Nozzle Range | 240-260°C |
| Bed Range | 90-110°C |
| Speed Range | 40-60 mm/s |
| Difficulty | intermediate |
| Drying | 77°C / 4h |
| Enclosure | Recommended |
ASA at a Glance
Strengths
- Best UV resistance of common filaments (10x better than ABS)
- Excellent for outdoor functional parts
- Does not yellow or become brittle in sunlight
- Good impact resistance (similar to ABS)
- Good heat resistance (softens ~100C)
Weaknesses
- Requires enclosure (like ABS)
- Emits fumes (similar to ABS)
- More expensive than ABS
- Still prone to warping without enclosure
Want personalized AI settings?
Describe your exact setup and what you are printing. 3DSearch's AI expert generates custom slicer settings for your Snapmaker J1 with ASA in seconds.
Try 3DSearch →Sources: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. Values calculated from filament specifications and printer hardware limits.