Recycled PLA Settings for Creality CR-6 SE
Recommended slicer settings for printing Recycled PLA on the Creality CR-6 SE (235 x 235 x 250 mm build volume, 100 mm/s max speed, Bowden extruder).
Конфигурация слайсера
Скопируй эти значения в свой слайсер (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| Параметр | Значение | Диапазон |
|---|---|---|
| Температура сопла | 205°C | 190-220°C |
| Температура стола | 55°C | 50-60°C |
| Сопло первого слоя | 210°C | +5°C above normal |
| Стол первого слоя | 60°C | +5°C above normal |
| Скорость печати | 40 mm/s | 30-50 mm/s |
| Скорость первого слоя | 15 mm/s | 25-50% of normal |
| Скорость стен | 30 mm/s | 70-80% of normal |
| Скорость холостого хода | 75 mm/s | 120-150% of print speed |
| Высота слоя | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| Количество стен | 2-3 | Perimeters/shells |
| Верхние/нижние слои | 3-4 | Solid layers |
| Вентилятор охлаждения | 100% | From layer 2+ |
| Расстояние втягивания | 4-6 mm | Bowden |
| Скорость втягивания | 40 mm/s | Bowden |
Перед печатью
Профили качества печати
Three presets for common use cases with Recycled PLA on the Creality CR-6 SE.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
Адгезия стола
Переработанный PLA прилипает как обычный PLA, но качество может варьироваться.
Руководство по регулировке температуры
Nozzle: 205°C
Range: 190-220°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 55°C
Range: 50-60°C. Printer max: 110°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
Устранение неполадок Recycled PLA на Creality CR-6 SE
Советы профессионалов для Recycled PLA
Переработанный PLA похож на обычный PLA, но с переменным качеством
Печатай температурные башни перед критическими деталями
Экологические преимущества очевидны - используй переработанный материал
Храни как обычный PLA
Материал дешевле, но возможно менее консистентен
Параметры поддержки
For prints requiring supports with Recycled PLA, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Creality CR-6 SE Specs
| Build Volume | 235 x 235 x 250 mm |
| Max Speed | 100 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 110°C |
| Extruder | Bowden |
Recycled PLA Properties
| Nozzle Range | 190-220°C |
| Bed Range | 50-60°C |
| Speed Range | 30-50 mm/s |
| Difficulty | beginner |
| Drying | Not required |
| Enclosure | Not needed |
Recycled PLA с первого взгляда
Сильные стороны
- Eco-friendly — made from recycled materials
- Similar properties to standard PLA
- Reduces plastic waste
- Good for non-critical parts
Слабые стороны
- Color consistency may vary between batches
- Slightly lower strength than virgin PLA
- Limited color selection
Хочешь персонализированные параметры ИИ?
Опиши свою точную конфигурацию и то, что ты печатаешь. Эксперт ИИ 3DSearch генерирует пользовательские параметры слайсера для твоего Creality CR-6 SE с Recycled PLA за секунды.
Попробуй 3DSearch →Источники: Based on Creality support documentation, community testing data, manufacturer recommended ranges. Значения рассчитаны на основе спецификаций филамента и ограничений аппаратного обеспечения принтера.