TPU 95A Settings for Creality Ender 3 S1 Pro
Recommended slicer settings for printing TPU 95A on the Creality Ender 3 S1 Pro (220 x 220 x 270 mm build volume, 150 mm/s max speed, direct drive extruder).
Slicer-configuratie
Kopieer deze waarden naar je slicer (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| Instelling | Waarde | Bereik |
|---|---|---|
| Mondstuktemperatuur | 223°C | 210-235°C |
| Bedtemperatuur | 50°C | 40-60°C |
| Eerste laag mondstuk | 228°C | +5°C above normal |
| Eerste laag bed | 55°C | +5°C above normal |
| Afdruksnelheid | 23 mm/s | 15-30 mm/s |
| Eerste laag snelheid | 15 mm/s | 25-50% of normal |
| Muursnelheid | 17 mm/s | 70-80% of normal |
| Reissnelheid | 45 mm/s | 120-150% of print speed |
| Laagdikte | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| Muurantal | 3-4 | Perimeters/shells |
| Boven-/onderlagen | 5-6 | Solid layers |
| Koelventilator | 100% | From layer 2+ |
| Intrekngsafstand | 0.8-1.2 mm | Direct drive |
| Intreksnelheid | 40 mm/s | Direct drive |
Voordat je afdrukt
Afdrukprofielen kwaliteit
Three presets for common use cases with TPU 95A on the Creality Ender 3 S1 Pro.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 30 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 23 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 15 mm/s | 20-30% | Miniatures, display pieces, fine detail |
Adhesie bed
TPU 95A hecht goed aan PEI-platen. Dit is de hardste TPU-variant met vergelijkbare hechting als TPU 87A.
Temperatuurafstemmingsgids
Nozzle: 223°C
Range: 210-235°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 50°C
Range: 40-60°C. Printer max: 110°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
Problemen oplossen TPU 95A op Creality Ender 3 S1 Pro
Pro tips voor TPU 95A
TPU 95A is de hardste en makkelijkste af te drukken TPU-variant
Druk op normale snelheden - 40-60 mm/s
Directe aandrijving wordt aanbevolen maar Bowden kan werken
Deze variant is toleranter voor beginners
Materiaal is ideaal voor stevige flexibele onderdelen
Ondersteuningsinstellingen
For prints requiring supports with TPU 95A, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Creality Ender 3 S1 Pro Specs
| Build Volume | 220 x 220 x 270 mm |
| Max Speed | 150 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 110°C |
| Extruder | Direct Drive |
TPU 95A Properties
| Nozzle Range | 210-235°C |
| Bed Range | 40-60°C |
| Speed Range | 15-30 mm/s |
| Difficulty | intermediate |
| Drying | 50°C / 5h |
| Enclosure | Not needed |
TPU 95A in één oogopslag
Sterke punten
- Standard flexible filament — Shore 95A hardness
- Good balance of flexibility and printability
- Excellent impact and abrasion resistance
- Stretches 300-500% before breaking
Zwakke punten
- Must print slowly
- Difficult on Bowden extruders — direct drive preferred
- Minimal retraction needed (causes jams)
- Stringing is common
Wil je gepersonaliseerde AI-instellingen?
Beschrijf je exacte setup en wat je afdrukt. 3DSearch's AI-expert genereert in seconden aangepaste slicer-instellingen voor je Creality Ender 3 S1 Pro met TPU 95A.
Probeer 3DSearch →Bronnen: Based on Creality support documentation, community testing data, manufacturer recommended ranges. Waarden berekend op basis van filamentspecificaties en printerhard warelimiet.