Carbon Fiber PLA Settings for Anycubic Kobra 2 Pro
Recommended slicer settings for printing Carbon Fiber PLA on the Anycubic Kobra 2 Pro (220 x 220 x 250 mm build volume, 500 mm/s max speed, direct drive extruder).
Slicer-configuratie
Kopieer deze waarden naar je slicer (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| Instelling | Waarde | Bereik |
|---|---|---|
| Mondstuktemperatuur | 215°C | 200-230°C |
| Bedtemperatuur | 58°C | 50-65°C |
| Eerste laag mondstuk | 220°C | +5°C above normal |
| Eerste laag bed | 63°C | +5°C above normal |
| Afdruksnelheid | 40 mm/s | 30-50 mm/s |
| Eerste laag snelheid | 15 mm/s | 25-50% of normal |
| Muursnelheid | 30 mm/s | 70-80% of normal |
| Reissnelheid | 75 mm/s | 120-150% of print speed |
| Laagdikte | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| Muurantal | 2-3 | Perimeters/shells |
| Boven-/onderlagen | 3-4 | Solid layers |
| Koelventilator | 100% | From layer 2+ |
| Intrekngsafstand | 0.8-1.2 mm | Direct drive |
| Intreksnelheid | 40 mm/s | Direct drive |
Voordat je afdrukt
Afdrukprofielen kwaliteit
Three presets for common use cases with Carbon Fiber PLA on the Anycubic Kobra 2 Pro.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
Adhesie bed
Koolstofvezel PLA hecht als normale PLA. Vezels kunnen oppervlakte-ruwheid creëren, wat soms hechting helpt. Gebruik PEI-platen of andere standaard oppervlakken.
Temperatuurafstemmingsgids
Nozzle: 215°C
Range: 200-230°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 58°C
Range: 50-65°C. Printer max: 110°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
Problemen oplossen Carbon Fiber PLA op Anycubic Kobra 2 Pro
Pro tips voor Carbon Fiber PLA
Zeker geharde of staal-nozzle gebruiken omdat Koolstofvezel erg abrasief is
Druk op vergelijkbare temperaturen als normale PLA, maar verhoog doorvoersnelheid met 10-15%
Koolstofvezel PLA is stijver en lichter dan normale PLA
Materiaal is ideaal voor functionele onderdelen die hoge stijfheid nodig hebben
Berg droog op als normale PLA
Ondersteuningsinstellingen
For prints requiring supports with Carbon Fiber PLA, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Anycubic Kobra 2 Pro Specs
| Build Volume | 220 x 220 x 250 mm |
| Max Speed | 500 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 110°C |
| Extruder | Direct Drive |
Carbon Fiber PLA Properties
| Nozzle Range | 200-230°C |
| Bed Range | 50-65°C |
| Speed Range | 30-50 mm/s |
| Difficulty | intermediate |
| Drying | Not required |
| Enclosure | Not needed |
Carbon Fiber PLA in één oogopslag
Sterke punten
- Much stiffer than regular PLA
- Reduced warping compared to PLA
- Professional matte surface finish
- Ideal for drone frames, brackets, fixtures
- Lightweight with structural rigidity
Zwakke punten
- Requires hardened steel nozzle (destroys brass)
- More brittle than regular PLA
- 25-50% slower print speeds needed
- Does not add tensile strength (short fibers)
- Use 0.5mm+ nozzle to prevent clogging
Wil je gepersonaliseerde AI-instellingen?
Beschrijf je exacte setup en wat je afdrukt. 3DSearch's AI-expert genereert in seconden aangepaste slicer-instellingen voor je Anycubic Kobra 2 Pro met Carbon Fiber PLA.
Probeer 3DSearch →Bronnen: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. Waarden berekend op basis van filamentspecificaties en printerhard warelimiet.