Wood PLA Settings for Anycubic Kobra 2 Neo
Recommended slicer settings for printing Wood PLA on the Anycubic Kobra 2 Neo (220 x 220 x 250 mm build volume, 250 mm/s max speed, direct drive extruder).
הגדרות Slicer
העתק את הערכים האלה ל-Slicer שלך (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| הגדרה | ערך | טווח |
|---|---|---|
| טמפרטורת חרירון | 195°C | 180-210°C |
| טמפרטורת משטח | 50°C | 40-60°C |
| חרירון בשכבה ראשונה | 200°C | +5°C above normal |
| משטח בשכבה ראשונה | 55°C | +5°C above normal |
| מהירות הדפסה | 40 mm/s | 30-50 mm/s |
| מהירות שכבה ראשונה | 15 mm/s | 25-50% of normal |
| מהירות דפנות | 30 mm/s | 70-80% of normal |
| מהירות תנועה | 75 mm/s | 120-150% of print speed |
| גובה שכבה | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| מספר דפנות | 2-3 | Perimeters/shells |
| שכבות עליונות/תחתונות | 3-4 | Solid layers |
| מאוורר קירור | 100% | From layer 2+ |
| מרחק נסיגה | 0.8-1.2 mm | Direct drive |
| מהירות נסיגה | 40 mm/s | Direct drive |
לפני שמדפיסים
פרופילי איכות הדפסה
Three presets for common use cases with Wood PLA on the Anycubic Kobra 2 Neo.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
היצמדות למשטח
Wood PLA adheres well to PEI sheets and glass beds with glue stick. Same adhesion approach as regular PLA. The wood fibers can make the first layer slightly rougher.
מדריך כיוון טמפרטורה
Nozzle: 195°C
Range: 180-210°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 50°C
Range: 40-60°C. Printer max: 110°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
פתרון תקלות Wood PLA על Anycubic Kobra 2 Neo
טיפים מקצועיים ל-Wood PLA
Experiment with temperature to control the wood color: lower temps = lighter, higher temps = darker
Use a 0.6mm nozzle to prevent clogging from wood particles
Never leave wood PLA idle in a hot nozzle -- the wood fibers will char and cause a permanent clog
Finished prints can be sanded and stained just like real wood for stunning results
Vase mode prints with wood PLA create beautiful, natural-looking decorative pieces
הגדרות תמיכות
For prints requiring supports with Wood PLA, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Anycubic Kobra 2 Neo Specs
| Build Volume | 220 x 220 x 250 mm |
| Max Speed | 250 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 110°C |
| Extruder | Direct Drive |
Wood PLA Properties
| Nozzle Range | 180-210°C |
| Bed Range | 40-60°C |
| Speed Range | 30-50 mm/s |
| Difficulty | intermediate |
| Drying | Not required |
| Enclosure | Not needed |
Wood PLA במבט מהיר
יתרונות
- Real wood-like appearance and feel
- Can be sanded, stained, and finished like real wood
- Temperature controls color (lower=lighter, higher=darker)
- Does not require hardened nozzle
- Great for decorative and artistic prints
חסרונות
- Prone to clogging (use 0.6mm nozzle recommended)
- Do not leave filament sitting hot in nozzle (chars)
- Inconsistent color (but adds to wood look)
- Slower print speeds needed
- Not for structural or functional parts
רוצה הגדרות AI מותאמות אישית?
תאר את ההגדרה המדויקת שלך ואת מה שאתה מדפיס. מומחה ה-AI של 3DSearch מייצר הגדרות סלייסר מותאמות עבור ה-Anycubic Kobra 2 Neo שלך עם Wood PLA תוך שניות.
נסה את 3DSearch →מקורות: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. הערכים חושבו ממפרטי הפילמנט וממגבלות החומרה של המדפסת.