Carbon Fiber PLA Settings for Bambu Lab H2C
Recommended slicer settings for printing Carbon Fiber PLA on the Bambu Lab H2C (330 x 320 x 325 mm build volume, 1000 mm/s max speed, direct drive extruder).
Slicer-Konfiguration
Kopiere diese Werte in deinen Slicer (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| Einstellung | Wert | Bereich |
|---|---|---|
| Düsentemperatur | 215°C | 200-230°C |
| Heizbetttemperatur | 58°C | 50-65°C |
| Erste Schicht Düse | 220°C | +5°C above normal |
| Erste Schicht Heizbett | 63°C | +5°C above normal |
| Druckgeschwindigkeit | 40 mm/s | 30-50 mm/s |
| Erste Schicht Geschwindigkeit | 15 mm/s | 25-50% of normal |
| Wandgeschwindigkeit | 30 mm/s | 70-80% of normal |
| Verfahrgeschwindigkeit | 75 mm/s | 120-150% of print speed |
| Schichthöhe | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| Wandanzahl | 2-3 | Perimeters/shells |
| Oben/Unten Schichten | 3-4 | Solid layers |
| Kühlventilator | 100% | From layer 2+ |
| Rückzugsdistanz | 0.8-1.2 mm | Direct drive |
| Rückzugsgeschwindigkeit | 40 mm/s | Direct drive |
Vor dem Drucken
Druckqualität Profile
Three presets for common use cases with Carbon Fiber PLA on the Bambu Lab H2C.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
Haftung des Heizbetts
Carbon Fiber PLA haftet wie normales PLA. Die Fasern können Oberflächenrauheit erzeugen, was die Haftung manchmal hilft. Verwende PEI-Bleche oder andere Standard-Oberflächen.
Temperatur-Abstimmungsanleitung
Nozzle: 215°C
Range: 200-230°C. Printer max: 350°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 58°C
Range: 50-65°C. Printer max: 120°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
Fehlerbehebung Carbon Fiber PLA auf Bambu Lab H2C
Pro-Tipps für Carbon Fiber PLA
Verwende unbedingt eine gehärtete oder Stahl-Düse, da Carbon Fiber sehr abrasiv ist
Drucke bei ähnlichen Temperaturen wie normales PLA, aber erhöhe die Durchsatzrate um 10-15%
Carbon Fiber PLA ist steifer und leichter als normales PLA
Das Material ist ideal für funktionelle Teile, die hohe Steifigkeit benötigen
Lagere trocken wie normales PLA
Support-Einstellungen
For prints requiring supports with Carbon Fiber PLA, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Bambu Lab H2C Specs
| Build Volume | 330 x 320 x 325 mm |
| Max Speed | 1000 mm/s |
| Max Nozzle Temp | 350°C |
| Max Bed Temp | 120°C |
| Extruder | Direct Drive |
Carbon Fiber PLA Properties
| Nozzle Range | 200-230°C |
| Bed Range | 50-65°C |
| Speed Range | 30-50 mm/s |
| Difficulty | intermediate |
| Drying | Not required |
| Enclosure | Not needed |
Carbon Fiber PLA auf einen Blick
Stärken
- Much stiffer than regular PLA
- Reduced warping compared to PLA
- Professional matte surface finish
- Ideal for drone frames, brackets, fixtures
- Lightweight with structural rigidity
Schwächen
- Requires hardened steel nozzle (destroys brass)
- More brittle than regular PLA
- 25-50% slower print speeds needed
- Does not add tensile strength (short fibers)
- Use 0.5mm+ nozzle to prevent clogging
Möchtest du personalisierte KI-Einstellungen?
Beschreibe dein genaues Setup und was du druckst. 3DSearch's KI-Experte erzeugt in Sekunden individuelle Slicer-Einstellungen für deinen Bambu Lab H2C mit Carbon Fiber PLA.
3DSearch ausprobieren →Quellen: Based on Bambu Lab Wiki (wiki.bambulab.com), community testing data, manufacturer recommended ranges. Werte berechnet aus Filament-Spezifikationen und Drucker-Hardware-Limits.