TPE Settings for QIDI X-CF Pro
Recommended slicer settings for printing TPE on the QIDI X-CF Pro (300x250x300 build volume, 100 mm/s max speed, direct drive extruder).
إعدادات Slicer
انسخ هذه القيم إلى Slicer الخاص بك (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| الإعداد | القيمة | النطاق |
|---|---|---|
| درجة حرارة الفوهة | 215°C | 200-230°C |
| درجة حرارة المنصة | 40°C | 30-50°C |
| الفوهة للطبقة الأولى | 220°C | +5°C above normal |
| المنصة للطبقة الأولى | 45°C | +5°C above normal |
| سرعة الطباعة | 18 mm/s | 10-25 mm/s |
| سرعة الطبقة الأولى | 15 mm/s | 25-50% of normal |
| سرعة الجدران | 14 mm/s | 70-80% of normal |
| سرعة الانتقال | 38 mm/s | 120-150% of print speed |
| ارتفاع الطبقة | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| عدد الجدران | 3-4 | Perimeters/shells |
| الطبقات العلوية/السفلية | 5-6 | Solid layers |
| مروحة التبريد | 100% | From layer 2+ |
| مسافة السحب | 0.8-1.2 mm | Direct drive |
| سرعة السحب | 40 mm/s | Direct drive |
قبل أن تطبع
ملفات تعريف جودة الطباعة
Three presets for common use cases with TPE on the QIDI X-CF Pro.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 25 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 18 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 10 mm/s | 20-30% | Miniatures, display pieces, fine detail |
التصاق بالمنصة
TPE adheres well to PEI sheets and blue painter's tape. Like TPU, adhesion is generally not a problem with flexible filaments. Use a slow first-layer speed for best results.
دليل ضبط درجة الحرارة
Nozzle: 215°C
Range: 200-230°C. Printer max: 350°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 40°C
Range: 30-50°C. Printer max: 120°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
استكشاف أخطاء TPE على QIDI X-CF Pro
نصائح احترافية لـ TPE
TPE is softer than standard TPU -- direct drive extruder is essentially mandatory
Print at 15-30 mm/s; speed is the number one cause of TPE printing failures
Minimize retraction to 0.3-0.8mm on direct drive; Bowden is not recommended
TPE excels for gaskets, soft grips, and wearable items due to its skin-safe flexibility
إعدادات الدعائم
For prints requiring supports with TPE, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
QIDI X-CF Pro Specs
| Build Volume | 300x250x300 |
| Max Speed | 100 mm/s |
| Max Nozzle Temp | 350°C |
| Max Bed Temp | 120°C |
| Extruder | Direct Drive |
TPE Properties
| Nozzle Range | 200-230°C |
| Bed Range | 30-50°C |
| Speed Range | 10-25 mm/s |
| Difficulty | advanced |
| Drying | 50°C / 5h |
| Enclosure | Not needed |
TPE في لمحة
نقاط القوة
- Softer than TPU — very rubber-like
- Excellent elasticity and memory
- Good for very flexible parts
- Chemical resistant
نقاط الضعف
- Extremely difficult to print
- Direct drive required — impossible on Bowden
- Very slow speeds only
- Poor detail resolution due to softness
تريد إعدادات AI مخصصة؟
صِف إعدادك الدقيق وما تطبعه. يُنشئ خبير AI في 3DSearch إعدادات تقطيع مخصصة لطابعتك QIDI X-CF Pro مع TPE خلال ثوانٍ.
جرّب 3DSearch →المصادر: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. تم حساب القيم من مواصفات الفيلامنت وحدود عتاد الطابعة.