PVA Settings for Creality Ender 3 V2 Neo
Recommended slicer settings for printing PVA on the Creality Ender 3 V2 Neo (220 x 220 x 250 mm build volume, 120 mm/s max speed, Bowden extruder).
إعدادات Slicer
انسخ هذه القيم إلى Slicer الخاص بك (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| الإعداد | القيمة | النطاق |
|---|---|---|
| درجة حرارة الفوهة | 200°C | 185-215°C |
| درجة حرارة المنصة | 55°C | 50-60°C |
| الفوهة للطبقة الأولى | 205°C | +5°C above normal |
| المنصة للطبقة الأولى | 60°C | +5°C above normal |
| سرعة الطباعة | 25 mm/s | 20-30 mm/s |
| سرعة الطبقة الأولى | 15 mm/s | 25-50% of normal |
| سرعة الجدران | 19 mm/s | 70-80% of normal |
| سرعة الانتقال | 45 mm/s | 120-150% of print speed |
| ارتفاع الطبقة | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| عدد الجدران | 2-3 | Perimeters/shells |
| الطبقات العلوية/السفلية | 3-4 | Solid layers |
| مروحة التبريد | 100% | From layer 2+ |
| مسافة السحب | 4-6 mm | Bowden |
| سرعة السحب | 40 mm/s | Bowden |
قبل أن تطبع
ملفات تعريف جودة الطباعة
Three presets for common use cases with PVA on the Creality Ender 3 V2 Neo.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 30 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 25 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 20 mm/s | 20-30% | Miniatures, display pieces, fine detail |
التصاق بالمنصة
PVA is used as a support material and should adhere to whatever build surface your main material uses. Use a bed temperature of 50-60°C.
دليل ضبط درجة الحرارة
Nozzle: 200°C
Range: 185-215°C. Printer max: 260°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 55°C
Range: 50-60°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
استكشاف أخطاء PVA على Creality Ender 3 V2 Neo
نصائح احترافية لـ PVA
Store PVA in an airtight container at all times -- it literally dissolves in moisture
Print from a dry box and use the spool immediately after opening
Warm water (40-45°C) with gentle agitation dissolves PVA much faster
PVA works best with PLA as the main material due to similar print temperatures
Only use PVA when support quality truly matters -- it is expensive and moisture-sensitive
إعدادات الدعائم
PVA is itself a support material. Dissolve in warm water (up to 45°C) after printing. Set support interface Z-distance to 0mm for water-soluble supports.
Creality Ender 3 V2 Neo Specs
| Build Volume | 220 x 220 x 250 mm |
| Max Speed | 120 mm/s |
| Max Nozzle Temp | 260°C |
| Max Bed Temp | 100°C |
| Extruder | Bowden |
PVA Properties
| Nozzle Range | 185-215°C |
| Bed Range | 50-60°C |
| Speed Range | 20-30 mm/s |
| Difficulty | intermediate |
| Drying | 50°C / 5h |
| Enclosure | Not needed |
PVA في لمحة
نقاط القوة
- Water-soluble support material
- Leaves near-perfect supported surfaces
- Dissolves in tap water (2-12 hours)
- Best paired with PLA
- No manual support removal needed
نقاط الضعف
- Extremely moisture sensitive (dissolves in water)
- Expensive (~$40-60/kg)
- Requires dual-extruder setup
- Must be stored in airtight container at all times
- Brittle when moisture-damaged
تريد إعدادات AI مخصصة؟
صِف إعدادك الدقيق وما تطبعه. يُنشئ خبير AI في 3DSearch إعدادات تقطيع مخصصة لطابعتك Creality Ender 3 V2 Neo مع PVA خلال ثوانٍ.
جرّب 3DSearch →المصادر: Based on Creality support documentation, community testing data, manufacturer recommended ranges. تم حساب القيم من مواصفات الفيلامنت وحدود عتاد الطابعة.