PHA Settings for Bambu Lab X1 Carbon
Recommended slicer settings for printing PHA on the Bambu Lab X1 Carbon (256 x 256 x 256 mm build volume, 500 mm/s max speed, direct drive extruder).
إعدادات Slicer
انسخ هذه القيم إلى Slicer الخاص بك (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| الإعداد | القيمة | النطاق |
|---|---|---|
| درجة حرارة الفوهة | 188°C | 175-200°C |
| درجة حرارة المنصة | 50°C | 40-60°C |
| الفوهة للطبقة الأولى | 193°C | +5°C above normal |
| المنصة للطبقة الأولى | 55°C | +5°C above normal |
| سرعة الطباعة | 35 mm/s | 25-45 mm/s |
| سرعة الطبقة الأولى | 15 mm/s | 25-50% of normal |
| سرعة الجدران | 26 mm/s | 70-80% of normal |
| سرعة الانتقال | 68 mm/s | 120-150% of print speed |
| ارتفاع الطبقة | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| عدد الجدران | 2-3 | Perimeters/shells |
| الطبقات العلوية/السفلية | 3-4 | Solid layers |
| مروحة التبريد | 100% | From layer 2+ |
| مسافة السحب | 0.8-1.2 mm | Direct drive |
| سرعة السحب | 40 mm/s | Direct drive |
قبل أن تطبع
ملفات تعريف جودة الطباعة
Three presets for common use cases with PHA on the Bambu Lab X1 Carbon.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 45 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 35 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 25 mm/s | 20-30% | Miniatures, display pieces, fine detail |
التصاق بالمنصة
PHA (polyhydroxyalkanoate) adheres similarly to PLA. Use a clean PEI sheet or glass bed with glue stick at 50-60°C. PHA is biodegradable and slightly more flexible than PLA.
دليل ضبط درجة الحرارة
Nozzle: 188°C
Range: 175-200°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 50°C
Range: 40-60°C. Printer max: 120°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
استكشاف أخطاء PHA على Bambu Lab X1 Carbon
نصائح احترافية لـ PHA
PHA is fully biodegradable and compostable -- a greener alternative to PLA
Print settings are very similar to PLA; start with PLA settings and adjust from there
PHA is slightly more flexible than PLA and less brittle on impact
Store in a cool, dry place; PHA biodegrades faster in humid environments
إعدادات الدعائم
For prints requiring supports with PHA, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Bambu Lab X1 Carbon Specs
| Build Volume | 256 x 256 x 256 mm |
| Max Speed | 500 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 120°C |
| Extruder | Direct Drive |
PHA Properties
| Nozzle Range | 175-200°C |
| Bed Range | 40-60°C |
| Speed Range | 25-45 mm/s |
| Difficulty | beginner |
| Drying | Not required |
| Enclosure | Not needed |
PHA في لمحة
نقاط القوة
- Fully biodegradable in soil and marine environments
- Renewable bioplastic from bacterial fermentation
- Non-toxic and biocompatible
- Easier to print than PLA in some cases
نقاط الضعف
- Lower heat resistance than PLA (~55°C)
- More expensive than PLA
- Limited availability and color options
- Slower degradation rate than marketed
تريد إعدادات AI مخصصة؟
صِف إعدادك الدقيق وما تطبعه. يُنشئ خبير AI في 3DSearch إعدادات تقطيع مخصصة لطابعتك Bambu Lab X1 Carbon مع PHA خلال ثوانٍ.
جرّب 3DSearch →المصادر: Based on Bambu Lab Wiki (wiki.bambulab.com), community testing data, manufacturer recommended ranges. تم حساب القيم من مواصفات الفيلامنت وحدود عتاد الطابعة.