TPU 95A Settings for Bambu Lab A1
Recommended slicer settings for printing TPU 95A on the Bambu Lab A1 (256 x 256 x 256 mm build volume, 500 mm/s max speed, direct drive extruder).
إعدادات Slicer
انسخ هذه القيم إلى Slicer الخاص بك (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| الإعداد | القيمة | النطاق |
|---|---|---|
| درجة حرارة الفوهة | 223°C | 210-235°C |
| درجة حرارة المنصة | 50°C | 40-60°C |
| الفوهة للطبقة الأولى | 228°C | +5°C above normal |
| المنصة للطبقة الأولى | 55°C | +5°C above normal |
| سرعة الطباعة | 23 mm/s | 15-30 mm/s |
| سرعة الطبقة الأولى | 15 mm/s | 25-50% of normal |
| سرعة الجدران | 17 mm/s | 70-80% of normal |
| سرعة الانتقال | 45 mm/s | 120-150% of print speed |
| ارتفاع الطبقة | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| عدد الجدران | 3-4 | Perimeters/shells |
| الطبقات العلوية/السفلية | 5-6 | Solid layers |
| مروحة التبريد | 100% | From layer 2+ |
| مسافة السحب | 0.8-1.2 mm | Direct drive |
| سرعة السحب | 40 mm/s | Direct drive |
قبل أن تطبع
ملفات تعريف جودة الطباعة
Three presets for common use cases with TPU 95A on the Bambu Lab A1.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 30 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 23 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 15 mm/s | 20-30% | Miniatures, display pieces, fine detail |
التصاق بالمنصة
TPU 95A (Shore 95A) adheres well to most surfaces including PEI sheets, blue painter's tape, and glass with glue stick. Adhesion is rarely an issue — the flexibility helps it grip the bed.
دليل ضبط درجة الحرارة
Nozzle: 223°C
Range: 210-235°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 50°C
Range: 40-60°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
استكشاف أخطاء TPU 95A على Bambu Lab A1
نصائح احترافية لـ TPU 95A
Shore 95A is the most common and easiest TPU to print -- start here if new to flexible filaments
Speed is everything: 20-40 mm/s maximum, slower for complex geometry
Minimize retraction (0.5-1mm direct drive) -- excessive retraction jams flexible filaments
Dry before use in humid climates; TPU is hygroscopic
إعدادات الدعائم
For prints requiring supports with TPU 95A, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Bambu Lab A1 Specs
| Build Volume | 256 x 256 x 256 mm |
| Max Speed | 500 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 100°C |
| Extruder | Direct Drive |
TPU 95A Properties
| Nozzle Range | 210-235°C |
| Bed Range | 40-60°C |
| Speed Range | 15-30 mm/s |
| Difficulty | intermediate |
| Drying | 50°C / 5h |
| Enclosure | Not needed |
TPU 95A في لمحة
نقاط القوة
- Standard flexible filament — Shore 95A hardness
- Good balance of flexibility and printability
- Excellent impact and abrasion resistance
- Stretches 300-500% before breaking
نقاط الضعف
- Must print slowly
- Difficult on Bowden extruders — direct drive preferred
- Minimal retraction needed (causes jams)
- Stringing is common
تريد إعدادات AI مخصصة؟
صِف إعدادك الدقيق وما تطبعه. يُنشئ خبير AI في 3DSearch إعدادات تقطيع مخصصة لطابعتك Bambu Lab A1 مع TPU 95A خلال ثوانٍ.
جرّب 3DSearch →المصادر: Based on Bambu Lab Wiki (wiki.bambulab.com), community testing data, manufacturer recommended ranges. تم حساب القيم من مواصفات الفيلامنت وحدود عتاد الطابعة.