Glow-in-the-dark PLA Settings for Bambu Lab A1
Recommended slicer settings for printing Glow-in-the-dark PLA on the Bambu Lab A1 (256 x 256 x 256 mm build volume, 500 mm/s max speed, direct drive extruder).
إعدادات Slicer
انسخ هذه القيم إلى Slicer الخاص بك (Cura, OrcaSlicer, PrusaSlicer, Bambu Studio)| الإعداد | القيمة | النطاق |
|---|---|---|
| درجة حرارة الفوهة | 210°C | 195-225°C |
| درجة حرارة المنصة | 55°C | 50-60°C |
| الفوهة للطبقة الأولى | 215°C | +5°C above normal |
| المنصة للطبقة الأولى | 60°C | +5°C above normal |
| سرعة الطباعة | 40 mm/s | 30-50 mm/s |
| سرعة الطبقة الأولى | 15 mm/s | 25-50% of normal |
| سرعة الجدران | 30 mm/s | 70-80% of normal |
| سرعة الانتقال | 75 mm/s | 120-150% of print speed |
| ارتفاع الطبقة | 0.2mm | 0.12-0.28mm |
| Infill | 15-20% | 10-30% |
| عدد الجدران | 2-3 | Perimeters/shells |
| الطبقات العلوية/السفلية | 3-4 | Solid layers |
| مروحة التبريد | 100% | From layer 2+ |
| مسافة السحب | 0.8-1.2 mm | Direct drive |
| سرعة السحب | 40 mm/s | Direct drive |
قبل أن تطبع
ملفات تعريف جودة الطباعة
Three presets for common use cases with Glow-in-the-dark PLA on the Bambu Lab A1.
| Profile | Layer Height | Speed | Infill | Best For |
|---|---|---|---|---|
| Draft | 0.28mm | 50 mm/s | 10-15% | Rapid prototyping, test fits |
| Standard | 0.20mm | 40 mm/s | 15-20% | General purpose, everyday prints |
| Quality | 0.12mm | 30 mm/s | 20-30% | Miniatures, display pieces, fine detail |
التصاق بالمنصة
Glow-in-the-dark PLA adheres like regular PLA. A clean PEI sheet or glass with glue stick works well. Note: glow PLA is abrasive and will wear out brass nozzles over time.
دليل ضبط درجة الحرارة
Nozzle: 210°C
Range: 195-225°C. Printer max: 300°C.
- Poor layer adhesion? Increase +5°C
- Stringing or oozing? Decrease -5°C
- Print a temperature tower to find your exact sweet spot
Bed: 55°C
Range: 50-60°C. Printer max: 100°C.
- First layer lifting? Increase +5°C
- Elephant's foot? Decrease -5°C
- Let the bed fully preheat before starting
استكشاف أخطاء Glow-in-the-dark PLA على Bambu Lab A1
نصائح احترافية لـ Glow-in-the-dark PLA
Use a hardened steel nozzle -- glow particles are abrasive and destroy brass nozzles
Charge prints under bright light or UV for maximum glow intensity and duration
Print with thin walls for better light penetration and stronger glow effect
White or clear glow PLA glows brightest; darker colors glow less
إعدادات الدعائم
For prints requiring supports with Glow-in-the-dark PLA, use tree supports for easier removal and less scarring. Set a 0.15-0.2mm Z-distance between support and model. If you have a dual-extruder setup, consider PVA (for PLA/PETG) or HIPS (for ABS) as dedicated water/solvent-soluble support material.
Bambu Lab A1 Specs
| Build Volume | 256 x 256 x 256 mm |
| Max Speed | 500 mm/s |
| Max Nozzle Temp | 300°C |
| Max Bed Temp | 100°C |
| Extruder | Direct Drive |
Glow-in-the-dark PLA Properties
| Nozzle Range | 195-225°C |
| Bed Range | 50-60°C |
| Speed Range | 30-50 mm/s |
| Difficulty | beginner |
| Drying | Not required |
| Enclosure | Not needed |
Glow-in-the-dark PLA في لمحة
نقاط القوة
- Charges in light and glows in the dark
- Fun for decorative and safety items
- Prints like standard PLA
نقاط الضعف
- Phosphorescent particles are abrasive — hardened nozzle required
- Limited to green/blue glow colors
- Glow fades over minutes without recharging
- Surface finish is slightly grainy
تريد إعدادات AI مخصصة؟
صِف إعدادك الدقيق وما تطبعه. يُنشئ خبير AI في 3DSearch إعدادات تقطيع مخصصة لطابعتك Bambu Lab A1 مع Glow-in-the-dark PLA خلال ثوانٍ.
جرّب 3DSearch →المصادر: Based on Bambu Lab Wiki (wiki.bambulab.com), community testing data, manufacturer recommended ranges. تم حساب القيم من مواصفات الفيلامنت وحدود عتاد الطابعة.