PEEK Settings for UltiMaker S8

Recommended slicer settings for printing PEEK on the UltiMaker S8 (330 x 240 x 300 mm build volume, 600 mm/s max speed, direct drive extruder).

Uyumlu Değiladvanced

Uyumlu Değil

The UltiMaker S8 has a max nozzle temperature of 300°C, which may be below the minimum recommended 370°C for PEEK. Printing may be possible at the lower end of the temperature range but results may be suboptimal.

Filament Nozzle Requirement370-420°C
Printer Max Nozzle300°C
Filament Bed Requirement130-160°C
Printer Max Bed140°C

Bunun yerine yapılması gerekenler

  • Your printer's hotend maxes out at 300°C, but PEEK needs at least 370°C. No amount of tuning can overcome this hardware limitation.
  • Try a compatible filament for your UltiMaker S8 — PLA, PETG, and ABS are good options.
  • If you need PEEK specifically, you'll need a printer with an all-metal hotend rated for 370°C+ nozzle and 130°C+ heated bed.

PEEK Requirements

PEEK Properties

Nozzle Range370-420°C
Bed Range130-160°C
Speed Range15-30 mm/s
Difficultyadvanced
EnclosureRequired
Drying150°C / 6h

UltiMaker S8 Specs

Build Volume330 x 240 x 300 mm
Max Speed600 mm/s
Max Nozzle Temp300°C
Max Bed Temp140°C
ExtruderDirect Drive

PEEK Bir Bakışta

Güçlü Yönleri

  • Heat resistance up to 250°C continuous
  • Exceptional chemical resistance
  • Aerospace and medical grade material
  • Biocompatible grades available

Zayıf Yönleri

  • Requires specialized printer (400°C+ hotend, heated enclosure)
  • Extremely expensive (~$300-700/kg)
  • Needs heated chamber at 120°C+
  • Cannot be printed on consumer-grade machines

Kişiselleştirilmiş yapay zeka ayarları ister misin?

Tam kurulumunu ve ne yazdırdığını açıkla. 3DSearch'ün yapay zeka uzmanı saniyeler içinde PEEK ile UltiMaker S8 için özel slicer ayarları oluşturuyor.

3DSearch'ü dene →

Kaynaklar: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. Değerler filament belirtimleri ve yazıcı donanım sınırlarından hesaplanmıştır.

UltiMaker S8 üzerinde Diğer Filamentler

PLA

205°C / 55°C100-300 mm/s

PLA+

215°C / 60°C100-300 mm/s

PETG

240°C / 85°C60-150 mm/s

ABS

245°C / 103°C60-200 mm/s

ASA

250°C / 100°C50-150 mm/s

TPU

225°C / 50°C20-50 mm/s

Diğer Yazıcılar üzerinde PEEK

UltiMaker Factor 4

340°C / 120°C15-30 mm/s

UltiMaker Method

300°C / 110°C15-30 mm/s

UltiMaker Method X

300°C / 110°C15-30 mm/s

UltiMaker Method XL

300°C / 110°C15-30 mm/s

UltiMaker S3

280°C / 85°C15-30 mm/s

UltiMaker S5

280°C / 140°C15-30 mm/s