PEEK Settings for UltiMaker S5

Recommended slicer settings for printing PEEK on the UltiMaker S5 (330 x 240 x 300 mm build volume, 300 mm/s max speed, direct drive extruder).

Uyumlu Değiladvanced

Uyumlu Değil

The UltiMaker S5 has a max nozzle temperature of 280°C, which may be below the minimum recommended 370°C for PEEK. Printing may be possible at the lower end of the temperature range but results may be suboptimal.

Filament Nozzle Requirement370-420°C
Printer Max Nozzle280°C
Filament Bed Requirement130-160°C
Printer Max Bed140°C

Bunun yerine yapılması gerekenler

  • Your printer's hotend maxes out at 280°C, but PEEK needs at least 370°C. No amount of tuning can overcome this hardware limitation.
  • Try a compatible filament for your UltiMaker S5 — PLA, PETG, and ABS are good options.
  • If you need PEEK specifically, you'll need a printer with an all-metal hotend rated for 370°C+ nozzle and 130°C+ heated bed.

PEEK Requirements

PEEK Properties

Nozzle Range370-420°C
Bed Range130-160°C
Speed Range15-30 mm/s
Difficultyadvanced
EnclosureRequired
Drying150°C / 6h

UltiMaker S5 Specs

Build Volume330 x 240 x 300 mm
Max Speed300 mm/s
Max Nozzle Temp280°C
Max Bed Temp140°C
ExtruderDirect Drive

PEEK Bir Bakışta

Güçlü Yönleri

  • Heat resistance up to 250°C continuous
  • Exceptional chemical resistance
  • Aerospace and medical grade material
  • Biocompatible grades available

Zayıf Yönleri

  • Requires specialized printer (400°C+ hotend, heated enclosure)
  • Extremely expensive (~$300-700/kg)
  • Needs heated chamber at 120°C+
  • Cannot be printed on consumer-grade machines

Kişiselleştirilmiş yapay zeka ayarları ister misin?

Tam kurulumunu ve ne yazdırdığını açıkla. 3DSearch'ün yapay zeka uzmanı saniyeler içinde PEEK ile UltiMaker S5 için özel slicer ayarları oluşturuyor.

3DSearch'ü dene →

Kaynaklar: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. Değerler filament belirtimleri ve yazıcı donanım sınırlarından hesaplanmıştır.

UltiMaker S5 üzerinde Diğer Filamentler

PLA

205°C / 55°C100-300 mm/s

PLA+

215°C / 60°C100-300 mm/s

PETG

240°C / 85°C60-150 mm/s

ABS

245°C / 103°C60-200 mm/s

ASA

250°C / 100°C50-150 mm/s

TPU

225°C / 50°C20-50 mm/s

Diğer Yazıcılar üzerinde PEEK

UltiMaker Factor 4

340°C / 120°C15-30 mm/s

UltiMaker Method

300°C / 110°C15-30 mm/s

UltiMaker Method X

300°C / 110°C15-30 mm/s

UltiMaker Method XL

300°C / 110°C15-30 mm/s

UltiMaker S3

280°C / 85°C15-30 mm/s

UltiMaker S6

280°C / 140°C15-30 mm/s