PEEK Settings for UltiMaker Factor 4

Recommended slicer settings for printing PEEK on the UltiMaker Factor 4 (330 x 240 x 300 mm build volume, 350 mm/s max speed, direct drive extruder).

غير متوافقadvanced

غير متوافق

The UltiMaker Factor 4 has a max nozzle temperature of 340°C, which may be below the minimum recommended 370°C for PEEK. Printing may be possible at the lower end of the temperature range but results may be suboptimal. The max bed temperature of 120°C is below the recommended 130°C for PEEK. Adhesion may be poor without additional bed adhesion aids.

Filament Nozzle Requirement370-420°C
Printer Max Nozzle340°C
Filament Bed Requirement130-160°C
Printer Max Bed120°C

ما الذي يجب فعله بدلاً من ذلك

  • Your printer's hotend maxes out at 340°C, but PEEK needs at least 370°C. No amount of tuning can overcome this hardware limitation.
  • Your printer's bed maxes out at 120°C, but PEEK needs at least 130°C for reliable adhesion.
  • Try a compatible filament for your UltiMaker Factor 4 — PLA, PETG, and ABS are good options.
  • If you need PEEK specifically, you'll need a printer with an all-metal hotend rated for 370°C+ nozzle and 130°C+ heated bed.

PEEK Requirements

PEEK Properties

Nozzle Range370-420°C
Bed Range130-160°C
Speed Range15-30 mm/s
Difficultyadvanced
EnclosureRequired
Drying150°C / 6h

UltiMaker Factor 4 Specs

Build Volume330 x 240 x 300 mm
Max Speed350 mm/s
Max Nozzle Temp340°C
Max Bed Temp120°C
ExtruderDirect Drive

PEEK في لمحة

نقاط القوة

  • Heat resistance up to 250°C continuous
  • Exceptional chemical resistance
  • Aerospace and medical grade material
  • Biocompatible grades available

نقاط الضعف

  • Requires specialized printer (400°C+ hotend, heated enclosure)
  • Extremely expensive (~$300-700/kg)
  • Needs heated chamber at 120°C+
  • Cannot be printed on consumer-grade machines

تريد إعدادات AI مخصصة؟

صِف إعدادك الدقيق وما تطبعه. يُنشئ خبير AI في 3DSearch إعدادات تقطيع مخصصة لطابعتك UltiMaker Factor 4 مع PEEK خلال ثوانٍ.

جرّب 3DSearch →

المصادر: Based on manufacturer specifications and community recommendations, community testing data, manufacturer recommended ranges. تم حساب القيم من مواصفات الفيلامنت وحدود عتاد الطابعة.

فيلامنتات أخرى على UltiMaker Factor 4

PLA

205°C / 55°C100-300 mm/s

PLA+

215°C / 60°C100-300 mm/s

PETG

240°C / 85°C60-150 mm/s

ABS

245°C / 103°C60-200 mm/s

ASA

250°C / 100°C50-150 mm/s

TPU

225°C / 50°C20-50 mm/s

PEEK على طابعات أخرى

UltiMaker Method

300°C / 110°C15-30 mm/s

UltiMaker Method X

300°C / 110°C15-30 mm/s

UltiMaker Method XL

300°C / 110°C15-30 mm/s

UltiMaker S3

280°C / 85°C15-30 mm/s

UltiMaker S5

280°C / 140°C15-30 mm/s

UltiMaker S6

280°C / 140°C15-30 mm/s